Guangdong Endurance Electronic Equipment Co., LtdMain products: testing machine
National Service Hotline :0086-13416787649 Wechat
Official wechat
Mobile
Mobile

Incoming solenoid valves only checked on/off? The NL-DCF-8 covers start-up, sealing, proof, flow and life in one bench

Popularity:9Time of publication:2026/11/16 20:43:45

Model: NL-DCF-8

The problem

An inlet solenoid valve costs a few dollars, yet its failure is the leading cause of water leakage, no-fill faults and error codes at the appliance line. Most factories only check on/off at incoming: start-up voltage, sealing at 0.84MPa, proof pressure at 1.75MPa and instantaneous flow after a 7.5s opening are all undocumented, so one diaphragm or mould change puts a whole batch at risk.

Capability

One bench covers both performance and life testing of dishwasher and washing machine water valves. Of the eight stations, one is a performance station fed by its own variable-frequency pump and seven are life stations sharing a circulating water system; stations can be selected freely and run at the same time. The performance station steps through start-up at 80 and 120 percent rated voltage within 1s, sealing at 0.03MPa and 0.84MPa static pressure for 1min each, proof pressure at 1.75MPa for 1min, flow at 0.1, 0.3 and 0.6MPa read 7.5s after opening, and endurance at 7.5s ON / 15s OFF for 30000 cycles with re-test afterwards. A low-pressure pump covers 0-0.5MPa and a high-pressure pump 0-1.75MPa, both variable frequency, so performance work is never limited by the life stations. Life stations set flow and pause time together with independent cycle settings, 0-999999s on/off timing and water pressure accumulated in 1, 3, 4 and 5 kgf/cm2 steps. The 80L tank runs at ambient to 32C; flow meters cover 2-15L/min at plus or minus 1 percent and pressure acquisition covers 0-1.6MPa. Two AC/DC voltage channels are manually adjustable with 0.1V and 0.01A display at class 0.5. An industrial touch computer with SCADA software keeps all settings through power loss, stops automatically at the set count or completed flow test, saves data, gives audible and visual notice, judges pass or fail and prints reports. Over-temperature alarm and protection, over-current protection and a buzzer are standard. The frame measures 1850x1250x1730mm with a 780mm table height, runs on AC380V/50Hz and moves on four heavy castors.

NL test equipment

NL test equipment

Applicable standards

GB/T 14536.9-2008 Particular requirements for electrically operated water valves, including mechanical requirements (current, identical to IEC 60730-2-8); GB/T 14536.1-2022 Automatic electrical controls, Part 1 General requirements; GB/T 4706.24-2024 washing machine particular requirements as the appliance level reference; test pressures, cycle steps and judgement values follow the customer technical agreement or product drawing.

Key specifications

  • Stations: 8 = 1 performance (independent pump) + 7 life (shared circulating water)
  • Performance items: start-up / sealing / proof pressure / flow / endurance
  • Start-up: 80 and 120 percent rated voltage, open and close within 1s
  • Sealing: 0.03MPa and 0.84MPa static pressure, 1min each
  • Proof pressure: 1.75MPa at inlet for 1min, no rupture or leakage
  • Flow: 0.1 / 0.3 / 0.6MPa, instantaneous flow 7.5s after opening
  • Endurance: 7.5s ON / 15s OFF, 30000 cycles, stepped water pressure
  • Water supply: low-pressure pump 0-0.5MPa, high-pressure pump 0-1.75MPa, both VFD
  • Tank: 80L, ambient to 32C
  • Flow meter: 2-15L/min, plus or minus 1 percent
  • Voltage / current: 2 AC-DC channels, 0.1V and 0.01A at class 0.5
  • Timing: on and off 0-999999s adjustable
  • Data: power-loss memory, auto judgement, statistics, storage, reports
  • Protection: over-temperature alarm and cut-out, over-current, buzzer

Applications

Factory batch inspection at water valve and inlet valve makers; incoming inspection at dishwasher and washing machine plants; valve performance and life verification in third-party laboratories; comparison after supplier mould or diaphragm changes

About the manufacturer

Guangdong Endurance Electronic Equipment Co., Ltd provides non-standard customization, drawing confirmation, factory acceptance, on-site installation and commissioning, operation training and long-term technical service; 12-month warranty and long-term spare parts supply. Tel: 0760-88500902 / 13416787649. Web: en.zsnaili.com.

Recommended products

Ranking of similar articles

Latest news articles