Guangdong Endurance Electronic Equipment Co., LtdMain products: testing machine
National Service Hotline :0086-13416787649 Wechat
Official wechat
Mobile
Mobile

The Same Pump Reads 48 m In-House and 45 m At the Third Party? NL-PSC-1 Pump Bench Flow Pressure Power In-Line Calibration Set (pump test bench)

Popularity:8Time of publication:2026/11/18 9:07:59

One pump measures 48 m head and 62% efficiency on the plant bench, then 45 m and 58% at a third-party laboratory. The customer arrives with both reports; the plant says the pump is fine and then looks at the bench. A turbine flowmeter had scaled, shifting its pulse factor by two percent; a pressure transmitter had gone two years without calibration and its zero had moved 0.03 MPa; the power meter sat on the drive input side and counted drive losses as shaft power. Three errors added up to four efficiency points. Bench error is not something a single annual calibration holds in check: flowmeters scale, transmitters drift, tappings clog, short straight lengths distort the velocity profile, and water temperature changes invalidate density and viscosity corrections. Most plants call someone in once a year and trust the numbers in between. When a dispute arises the measurement uncertainty of the bench cannot be produced, and the report loses its standing.

What the NL-PSC-1 in-line calibration set measures

  • One-piece construction spliced into the bench pipework, compared without removing instruments or stopping production (the metrology branch of our pump test bench range)
  • Flow calibration: master-meter and gravimetric channels, a 0.2 class master meter in series, pulse factor, linearity and repeatability given point by point
  • Pressure calibration: 0.05 class digital gauge and deadweight tester in two paths, tappings compared in situ, zero and span errors listed separately
  • Power calibration: three-phase analyser against a master meter, drive input and motor output connections distinguished, wiring loss metered separately
  • Speed calibration: photoelectric and magnetic channels, slip and speed ripple logged together
  • Temperature and density: inlet and outlet water temperature, density and viscosity measured in line, corrections fed into efficiency automatically
  • Tappings and straight length: tapping offset, burrs and clogging quantified, 5D, 10D and 15D straight lengths compared
  • Uncertainty: flow, pressure, power and speed components combined, expanded uncertainty of efficiency stated at 95% confidence
  • Comparison test: one pump measured at three duty points on this bench and on a standard rig, deviation and repeatability tabulated
  • Scaling and drift trend: quarterly comparison records kept, drift curves of meters and transmitters retrievable
  • Leakage: static hold and dynamic leakage of pipework and valves, effect on the flow reading quantified
  • Data chain: calibration records, raw data and correction factors exported in one go, reports filed to a laboratory management system
  • Supply and loop: test loop held on a pump performance test constant-pressure constant-flow basis, level on level sensor life test channels
  • Cross-category: the same method transfers to water and power channels of dishwasher test equipment and washing machine test equipment
  • Barcode binding: calibration points, deviations and uncertainty exported on one sheet, bench number and calibration interval traceable

Applicable standards

Rotodynamic pump hydraulic performance acceptance testing to GB/T 3216 (ISO 9906 basis), whose grade 1 accuracy sets explicit uncertainty limits for flow, pressure and power; flow standard facilities to JJG 643 and JJG 1030; pressure transmitters and digital gauges to JJG 882 and JJG 875; testing and calibration laboratory competence to GB/T 27025 (ISO/IEC 17025 basis). Calibration intervals, comparison frequency and deviation limits can follow the customer metrology policy.

Stations and throughput

One-piece in-line comparison without removing instruments completes a flow-pressure-power set in an hour, and one shift covers three straight lengths against two wiring arrangements. “Calibrated once a year, trusted in between” becomes a bench metrology record with deviation curves, uncertainty and drift trends. Bench acceptance, third-party disputes and customer audits all settle on one set.

Manufacturer

Guangdong Endurance Electronic Equipment Co., Ltd. — a non-standard testing equipment manufacturer of pump bench flow, pressure and power in-line calibration sets, pump test bench ranges, pump performance test systems, level sensor life test machines, dishwasher test equipment and washing machine test equipment.

Keywords: pump test bench, pump performance test, level sensor life test, dishwasher test equipment, washing machine test equipment.

Recommended products

Ranking of similar articles

Latest news articles