Guangdong Endurance Electronic Equipment Co., LtdMain products: testing machine
National Service Hotline :0086-13416787649 Wechat
Official wechat
Mobile
Mobile

A Straight Edge Is No Alignment: Hot Bearings and Weeping Seals in Six Months? NL-PAL-6 Pump-Motor Coupling Alignment and Radial Vibration Bench (pump test bench)

Popularity:10Time of publication:2026/11/13 9:15:24

On site the phrase is always the same: put a straight edge on it, looks lined up, good. Yet a coupling with 0.3 mm radial offset and half a degree of angular offset looks perfectly fine at standstill and behaves very differently once running. The elastomer inserts are sheared back and forth and ground to powder in a few months; the bearings carry an extra radial load and run a dozen degrees hotter, the grease ages first, then the outer ring spins and the races spall; the mechanical seal faces wobble, weep first and leak later; the pump curve quietly sags, a unit that measured 32 m³/h at the factory delivers 29 m³/h on site with no explanation. Soft foot, shim thickness, pipe strain and base stiffness all show up in the end as “bad coupling alignment”. Production tests the pump curve and the motor insulation, but how large the offset is, how vibration and temperature rise change with it, and where concentricity goes as the elastomer wears are never measured.

What the NL-PAL-6 coupling alignment and radial vibration bench measures

  • Six stations with quick-change interfaces for elastomer pin, jaw and disc couplings on 0.55–15 kW pump sets (the alignment post of our pump test bench installation range)
  • Radial and angular offset: laser alignment and dial gauge on two channels, 0–1.2 mm and 0–2.0 degrees in steps, logged step by step
  • Vibration severity: three points and three directions on the pump bearing housing, motor end shield and base, broadband levels tabulated to GB/T 29531
  • Bearing temperature rise: each offset step run to thermal equilibrium, rise curves plotted against offset, the safety margin made visible
  • Elastomer wear: ten thousand start-stops and continuous running as two paths, compression set, hardness, debris mass and post-wear concentricity recorded each time
  • Soft foot check: each of the four feet released in turn to measure displacement, soft-foot amount quantified against the vibration increase
  • Seal leakage: face leakage in mL/h logged on the same channel before and after each offset, seal failure separated from alignment error
  • Hydraulic coupling: H-Q curve and efficiency re-measured per offset step on a pump performance test basis, a family of curves showing the points lost
  • Noise and harmonics: first and second order amplitudes against offset, the spectral signature of misalignment calibrated for field diagnosis
  • Supply side on the level sensor life test level channels, tank level and suction pressure logged so cavitation and misalignment vibration can be told apart
  • Machine-level reference: small circulation pumps mounted in dishwasher test equipment and washing machine test equipment attitudes, installation stress effects traceable
  • Foot bolt torque and shim thickness programmable, assembly parameters tabulated with vibration data for the process card
  • Barcode binding, offset, vibration, temperature rise and leakage exported per unit for assembly station and lot traceability

Applicable standards

Rotodynamic pump hydraulic acceptance to GB/T 3216; pump vibration measurement and evaluation to GB/T 29531; vibration on non-rotating parts with reference to the relevant parts of GB/T 11348; coupling and pump-set installation to the equipment maker assembly specification. Vibration limits, temperature tolerances and leakage criteria can follow the customer standard, sampling to GB/T 2828.

Stations and throughput

Six stations map one pump set across an offset matrix in a day and complete a three-option assembly process record from first fit to ten thousand start-stops in a week. “Straight edge looks fine” becomes an installation report with offset values, vibration curves and leakage data. Assembly setting, coupling selection and after-sales vibration or leak complaints all settle on one bench.

Manufacturer

Guangdong Endurance Electronic Equipment Co., Ltd. — a non-standard testing equipment manufacturer of pump-motor coupling alignment and radial vibration benches, pump test bench ranges, pump performance test systems, level sensor life test machines, dishwasher test equipment and washing machine test equipment.

Keywords: pump test bench, pump performance test, level sensor life test, dishwasher test equipment, washing machine test equipment.

Recommended products

Ranking of similar articles

Latest news articles